CTS Cement
CTS Cement
Rapid Set

Ultra-Fast Anchoring Adhesive

Multi-Purpose Two-Component Structural Acrylate

DESCRIPTION: Rapid Set® Ultra-Fast Anchoring Adhesive is a two-component, high strength acrylate structural adhesive designed to develop a strong, durable bond to concrete, masonry, and other dissimilar building materials. The high-performance mechanical bond strength makes it suitable for use in a wide range of general construction, repair and maintenance projects.

USES: ULTRA-FAST ANCHORING ADHESIVE can be used on properly prepared concrete and masonry substrates and with other dissimilar building materials. It is ideal for anchoring bolts, dowels, rebar, and wall tiles to concrete, concrete blocks, solid and hollow masonry, natural stone, solid rock and other high strength substrates. Seek technical assistance when anchoring into porous or reconstituted stone. This bonded anchor is not intended for use as a cosmetic or decorative product. Due to the nature of the product, the resin may cause staining in certain materials. It is advisable to test the resin by applying it in a small, discrete area prior to using it on the project.

SURFACE PREPARATION: Ensure the substrate is clean, sound, dry and free of bond inhibitors, such as grease, oil, mold, coatings, sealers, or moisture. Do not install anchor in cracked, delaminated or weak substrates. Drill to the required diameter and depth with a roto-hammer or traditional drill and bit. Thoroughly remove all dust and debris from the application substrate.

APPLICATION: The minimum application temperature is 41°F (5°C) and rising. The maximum application temperature is 100°F (38°C). Cartridge temperature must be maintained at a minimum of 41°F (5°C). For best results, place adhesive when the ambient temperature is between 68°F and 77°F (20°C and 25°C). Ensure surface, personnel and equipment are ready before application. Remove screw top, pull up on the bag and cut carefully under the aluminum clip to open bag. Take the provided static mixing nozzle and screw onto the mouth of the cartridge. Insert the cartridge into a quality extrusion gun with a minimum of 18:1 thrust ratio. Before placing the nozzle into the hole, extrude material until an even gray color without streaks flows out of the nozzle. Insert the nozzle to the bottom of the hole. Extrude resin and slowly withdraw the nozzle keeping the tip immersed in the resin. Ensure no air voids are created as the nozzle is withdrawn. Insert the anchor, which must be free of oil or other release agents, to the bottom of the hole using a twisting motion. Do not withdraw and re-insert, as doing so would create air voids. Excess resin must be expelled from the hole evenly around the anchor. Leave the anchor to cure. Do not disturb the anchor until the material is set. Clean any excess resin from around the hole. Recommended annular space is less than 1/8" (3.1 mm).

CURING: Tack-free in 5 minutes, service ready in 50 minutes at 68°F to 77°F (20°C to 25°C).

Cartridge Temperature*
40°F (5°C)18 min40°F (5°C)24 hours
50°F (10°C)10 min50°F (10°C)145 min
60°F (16°C)6 min60°F (16°C)85 min
70°F (21°C)5 min70°F (21°C)50 min
80°F (27°C)4 min80°F (27°C)40 min
90°F (32°C)2 min90°F (32°C)35 min

*Cartridge temperature must be maintained at a minimum of 41°F (5°C).

*Cartridge temperature must be maintained at a minimum of 41°F (5°C).

COLD WEATHER: Installation in low temperatures will extend cure times of the Rapid Set® Ultra-Fast Anchoring Adhesive. To ease flow and placement in cold conditions, warm the adhesive above 70°F (21°C) for 24 hours prior to installation. Remove dew, frost or ice from the substrate with acetone on a clean cloth and place adhesive immediately.

WARM WEATHER: Installation in warmer temperatures at 80°F (27°C) and above will not adversely affect adhesive performance. Warmer temperatures will decrease viscosity and working/cure time.

CLEAN-UP: Clean up with acetone and disposable rags before it hardens on placement tools and surfaces. Dispose of waste material in compliance with local regulations.

PACKAGING: Ultra-Fast Anchoring Adhesive is available in a 10.1 fl. oz. (299 mL) cartridge.

SHELF LIFE: When stored correctly, the shelf life is 18 months from the date of manufacture.

STORAGE: Store in original, unopened container, the correct way up, in a cool, dry, area. Protect unopened container from water, heat and direct sunlight. Store at 41°F to 85°F (5°C to 29°C). Elevated temperatures will reduce shelf life.

LIMITATIONS: Not for use in cracked, delaminated or weak substrates. The National Transportation Safety Board (NTSB) has stated this product is approved for short-term loads only and should not be used in sustained tensile load adhesive anchoring applications or temperatures exceeding 176°F (80°C) where adhesive failure could result in a public safety risk. Consult a design professional prior to use. The design professional on the job is ultimately responsible for the interpretation of the data provided above.

USER RESPONSIBILITY: Before using, read current technical data sheets, bulletins, product labels and safety data sheets. It is the user’s responsibility to review the instructions and warnings for any CTS products prior to use. Wear chemical resistant gloves and protect eyes and skin during use. Do not attempt to force adhesive out of a hardened mixing nozzle. Use a new mixer nozzle to avoid rupturing the container. If a leak should develop, discontinue use immediately and use a new cartridge. While all reasonable care is taken in compiling technical data on the company’s products, all recommendations or suggestions regarding the use of such products are made without guarantee, since the conditions of use are beyond the control of the company. It is the responsibility of the customer to confirm that the product is fit for the purpose for which it is intended to be used.

WARNING: DO NOT BREATHE VAPORS. AVOID CONTACT WITH SKIN AND EYE. Use product in well ventilated areas. Forced local exhaust is recommended to effectively minimize exposure. NIOSH approved, organic vapor respirators are recommended in confined areas, or when conditions (such as heated polymer, sanding) may cause high vapor concentrations. Do not weld on, burn or torch any acrylate material. Hazardous vapor is released when an acrylate is burned. For additional information refer to the precautionary statement on the Safety Data Sheet.

Please refer to the SDS and www.CTScement.com for additional safety information regarding this material.

LIMITED WARRANTY: CTS Cement Manufacturing Corp. (CTS) warrants its materials to be of good quality and at its option, within 18 months from date of manufacture, will replace material proven defective or refund purchase price thereof, and such replacement or refund shall be the limit of CTS’s responsibility. Except for the foregoing, all warranties, expressed or implied, including merchantability and fitness for a particular purpose, are excluded. CTS shall not be liable for any consequential, incidental, or special damages arising directly or indirectly from the use of the materials.

WARNING: CANCER and REPRODUCTIVE HARM - www.P65Warnings.ca.gov

Ultra-Fast CURING: Tack-free in 5 minutes and service ready in 50 minutes
Excellent structural adhesion
Multi-Purpose: Horizontal, vertical and overhead
Interior/Exterior: Durable in tough environments
Variable range of anchoring depths
No expansion forces, avoiding breakout of concrete
High load capacities
Conforms to:
ASTM C-881 Type IV, Grade 3, Class A, B, C Modified Acrylate
MasterFormat® 2016
03 05 07Adhesives for Concrete
09 05 00Adhesives – Common Work Results, Finishes
99 00 00 Construction & Industrial Products
CTS Cement Manufacturing Corp. 12442 Knott St. Garden Grove, CA 92841 Tel: 800-929-3030 | Fax: 714-379-8270 Web: www.CTScement.com E-mail: info@CTScement.com

Color (when mixed)
Gel Time astm C8816 min
Density astm d1875100 lb/ft3
Compressive Strength astm d6958700 psi (24 hours)
10100 psi (7 days)
Tensile Strength astm d6381600 psi (24 hours)
1700 psi (7 days)
Tensile Modulus astm d638490,000 psi (24 hours)
650,000 psi (7 days)
Flexural Strength astm d7904000 psi (7 days)
Heat Deflection Temperature (HDT) astm d648176° F (7 days)
Volatile Organic Compounds (VOC) astm d236936 g/L
Note: ASTM Standards are current unless otherwise stated. Data obtained at 68°F (20°C)
VOC Compliance
Meets U.S EPA 40 CFR 59 Subpart C & D; CARB: California Air Resource Board; LADCO: Lake Michigan Air Directors Consortium (Illinois, Indiana, Michigan, Wisconsin); MRPO: Midwest Regional Planning Organization (Illinois, Indiana, Michigan, Ohio, Wisconsin); SCAQMD: South Coast Air Quality Management District (Los Angeles, Orange, Riverside, San Bernardino Counties); and CEPA/EC: Canada Environmental Protection Agency/Environment.
icon icon

USGBC and related logo is a trademark owned by the U.S. Green Building Council and is used by permission.